Home/ Custom Extruded Sheet/ Vinyl/ABS
Material

Vinyl/ABS

Vinyl/ABS from Rowmark — vinyl foam laminated over an ABS substrate for a textured, leather-like formed part. Van, marine, RV and ATV interiors. Supplied to order from Sparks, NV.

Overview
01

Looks hand-wrapped.
Forms in one piece.

Vinyl/ABS is a vinyl foam composite laminated over an ABS substrate. The face is textured and leather-like, with the give of a foam backing under it, so a formed part reads as though somebody wrapped it by hand — without the labour, the seams, or the adhesive failures that come with actually wrapping it. Rowmark's own description is the right one: a high-performance leather.

GRAINED FACE OUT VINYL FOAM ABS Grain Give Structure Laminated — grain, cushion and structure in one sheet
Three layers doing three jobs. The foam is what makes a hard formed panel feel soft under a hand, and it is why the part reads as upholstery rather than plastic.
Surface
Near Scratch-Proof
The grained vinyl face is close to impervious to scratching and marring — the failure mode that ruins a bare ABS interior panel in a working vehicle.
Feel
Foam Backed
A vinyl foam composite, not a printed film. It has give under a hand, which is what sells a dash or a door card as a finished interior.
Process
Thermoforms
Built for forming applications, over an ABS substrate that keeps its rigidity and takes the wear.

Stock & Sizes

Ordered in to your specification

We do not carry this on the rack. Grain, color and gauge are all chosen for the job, so it comes in as a specified order. Rowmark run the custom extruded line from 0.005″ through 0.325″, in widths to 74″, with custom color matching.

Send us the part, the draw depth and the finish you are matching. We are a Rowmark distributor, so this is a normal order rather than a special one — and if you are running volume, tell us, because that is the conversation that gets material put on our floor.

Two things to design around

Regrind cannot be reused. Adding the vinyl layer means your trim and skeleton do not go back into the process the way plain ABS scrap does. If you are running volume and costing the job on regrind recovery, take that out of the model before you quote it. This is Rowmark's own note, not a caveat we invented.

Depth of draw is slightly reduced. The laminate does not stretch quite as far as bare ABS, so a deep-draw part that works in plain sheet may need a gauge change or a tooling tweak. Worth proving on the first pull rather than discovering it mid-run.

Typical Properties

PropertyValueNotes
ConstructionVinyl foam composite over ABSLaminated
SurfaceTextured, leather-likeMimics hand-wrapped parts
Scratch & mar resistanceVery highThe main reason to specify it
SubstrateABSProvides rigidity and durability
Thickness range0.005″ – 0.325″Rowmark custom extruded range
Maximum width74″
ThermoformingYes — slightly reduced drawProve the depth on the first pull
RegrindNot reusableCost this out of the model
ApplicationInteriorVehicle, marine and RV interiors

Construction, limitations and range figures are Rowmark's published data for Vinyl/ABS and their custom extruded sheet line. For mechanical values the ABS substrate properties are the starting point — ask us for the mill data sheet on the specific build before you design to a number.

Where It Gets Used

Van & Conversion Interiors
Door cards, wall panels, headliner trim and console work in van conversions and explorer van builds.
Marine Dashboards
Helm dashes and console faces that need to look upholstered and survive sun, spray and hands.
RV & Recreational
Interior panels and trim for recreational vehicles, where a wrapped look is expected and labour is the cost driver.
ATV & Powersports
Components and trim on ATVs, side-by-sides and utility machines that take constant contact and abrasion.

Common Questions

Why use this instead of wrapping a part in vinyl?

Labour and failure modes. A wrapped part carries the cost of the wrapping operation, plus seams, plus an adhesive bond that can lift at an edge or in heat. Vinyl/ABS forms as one piece, so the grain follows the part with no seam and nothing to delaminate. On any run above a handful of parts the math usually favors the laminated sheet, and it is more consistent part to part.

Will it hold up in a vehicle interior in the sun?

The vinyl face is the wear and scratch surface and it is built for vehicle interiors — that is the market this product was designed for. For an interior seeing hard sun through glass, tell us the color and the exposure and we will confirm the grade with Rowmark before you commit. For anything genuinely exterior, this is the wrong product and Acrylic Capped ABS is the right one.

Can it be cut and machined normally?

Yes — it cuts and routs like ABS. We cut to size and CNC rout in Sparks. One thing to plan for: exposed cut edges show the layer stack, so on a visible edge you want a return, a trim, or a detail that hides it. Worth deciding at design rather than at assembly.

Do you stock it?

Not today. We stock Rowmark's engraving sheet and order the custom extruded line in per job. If you are building vans, boats or machines in volume and this would be a repeat order, say so — steady demand is exactly what would put it on our floor.

The material is already here. The clock starts when you order.

Made-to-order work does not go out in an hour, and we are not going to tell you it does. Here is what you actually get.

No wait on material
Cut from our own rack
We are not ordering your sheet from a mill and then starting your parts. The stock is here, so the job starts the day you approve the quote.
Scheduled
Lead time quoted with your price
You get a date with the number, not after you have committed. If we cannot hit the date you need, we say so on the quote instead of finding out later.
Free · Local
Delivered free when it is done
Finished parts go out on our own van across stock material and cut-to-size. No freight charge and no delivery minimum, or pick them up here in Sparks.
Free delivery · Reno · Sparks · Carson City · Fernley · USA Parkway  —  Cutoffs, coverage and FAQs →
(775) 358-8211
★★★★★

"Brought in a sketch on a napkin and they turned it into exactly what I needed. Same day."

— Sarah K. · Google Review
Get a Quote

Interested in Vinyl/ABS?
Tell us what you need.

Fill out the form below and we'll get back to you with a quote — most within the same day. Or call us at (775) 358-8211.

Quote Request Most quotes returned same day
This field is for validation purposes and should be left unchanged.
Name(Required)
Drop files here or
Accepted file types: jpg, jpeg, png, heic, heif, webp, pdf, doc, docx, csv, xls, xlsx, ai, eps, svg, dxf, dwg, step, stp, Max. file size: 25 MB, Max. files: 10.
    Fastest quote: 2D PDF technical drawing and DXF, in inches.No drawing? A photo of the part works fine, we will take it from there.

    Services
    01

    What we can do
    with this material.

    Every material and product we carry can be customized with our full range of fabrication services.

    Related

    You might also consider.

    Get Started

    Need Vinyl/ABS?
    Let's get it done.

    Walk into our Sparks shop with your measurements or call us — most quotes returned same day. No minimum order, free delivery in Reno, Sparks, Carson City, Fernley and USA Parkway.

    745 E. Greg St. #6, Sparks, NV 89431
    (775) 358-8211 · sales@silverstateplastics.com
    4.9
    ★★★★★
    Google Reviews
    Reno's Plastic Shop
    Call (775) 358-8211 Get a Quote →